Zanussi ZDF 222 Manuel d'utilisateur

User manualDishwasherZDF 222

Unscrew the cap.Only before filling withsalt for the first time, fillthe salt container with wa-ter.Using the funnel provided,pour in the salt until t

Filling with rinse aidOpen the lid.Fill up with rinse aid. Themaximum level for filling isindicated by "max"Clean up any rinse aidwhich over

Loading cutlery and dishesSponges, household cloths and any object thatcan absorb water may not be washed in thedishwasher.• Before loading the dishes

Load cutlery. For best re-sults we recommend youto use the cutlery grid pro-vided (if the size and di-mensions of the cutleryallow it)Place knives and

To move to the higher position proceed as follows:1. Pull out the basket until it stops.2. Carefully lift both sides upwards until the mecha-nism is e

For programmes with pre-wash add an additionaldetergent dose in com-partmentB.When using detergenttablets: place detergenttablets in compartment A.Clo

Clean filters A, B and Cthoroughly under runningwater.Turn the handle about 1/4turn anticlockwise and re-move filters B and C.Remove filter A from the

2. Leave the door ajar to prevent the forma-tion of any unpleasant smells.3. Leave the inside of the machine clean.Frost precautionsAvoid placing the

Something not workingThe dishwasher will not start or stops duringoperation.Certain problems are due to the lack of simplemaintenance or oversights, w

Once these checks have been carried out;close the dishwasher’s door and switch on theappliance. Press the button of the programmethat was running befo

Thank you for selecting ourapplianceWe wish you lots of enjoyment with your newappliance and we hope that you will considerour brand again when purcha

Technical dataDimensions Width x Height x Depth (cm) 60,0 x 85,0 x 61,0Electrical connectionVoltage - Overall power - FuseInformation on the electrica

Test in accordance with EN 50242 must becarried out when the salt container and rinseaid dispenser have been filled with salt andrinse aid respectivel

WARNING!Only use, for connection to the water mains,new hose-set; old hose-set must not be reused. CAUTION!If the machine is connected to new pipes

If you use a drain hose extension the totallength should not be longer than 4 metres.Likewise the internal diameter of the couplingsused for connectio

LevellingGood levelling is essential for correct closure andsealing of the door.When the appliance is correctly levelled, the door willnot catch on ei

7. The statutory warranty does not applywhen defects are caused by:– a chemical or electrochemical reactioncaused by water,– abnormal environmental co

Belgium Tel.:Fax.:Electrolux Home ProductsBelgium ELECTROLUXSERVICE Bergenses-teenweg 719 1502 Lem-beekConsumer services 02/363.04.44 02/363.04.0002/

www.electrolux.comAlbania +35 5 4 261 450 Rr. Pjeter Bogdani Nr. 7 TiraneBelgique/België/Belgien +32 2 363 04 44 Bergensesteenweg 719, 1502LembeekČesk

Portugal +35 12 14 40 39 39 Quinta da Fonte - Edificio Gon-çalves Zarco - Q 35 -2774-518Paço de ArcosRomania +40 21 451 20 30 Str. Garii Progresului 2

29

Safety informationIn the interest of your safety and to ensure thecorrect use, before installing and first using theappliance, read this user manual c

30

31

www.electrolux.com156994260-00-30052007Subject to change without notice

Installation• Check your dishwasher for any transportdamage. Never connect a damaged ma-chine. If your dishwasher is damaged con-tact your supplier.•

Programme selector dial and On/Off switch• when in this position, the machine is switched off(corresponding light off),• when the marker on the dial c

Indicator lightsWash indicator lightIlluminates when a washing programme is set and re-mains illuminated for all the duration of the washingprogramme.

Programme Degree of soil Type of load Programme descriptionBio 50°2)Normal soil Crockery and cutlery PrewashMain wash1 intermediate rinseFinal rinseDr

If you decide in future to use separated deter-gents, we advise that you:– Fill up the salt and rinse aid container.– Adjust the water hardness settin

Setting the water softener manually (see table)Set switch to position 1 or2The water softener is factory set at position 2.Setting the water softener