Zanussi TA833V Manuel d'utilisateur télécharger pdf (Page 2)

- 2 -

Installation

The floor must be clean and dry, free from floor polish and other

greasy substances, so that the machine does not slide about.

Do not use any grease as lubrification.

Installation on deep pile carpets and floor coverings with foam

backings is not recommended, as the stability of the machine

is no longer guaranteed. If the installation must be done on a

carpetedfloor, the openings located at the lower part of the back

of the appliance must remain free. These openings ensure a

good ventilation of your applicance. In case of small format

tiles, place a standard rubber mat under the machine.

With sprung floors, in particular wooden plank floors with

yielding floor boards, screw down a waterproof wooden base at

least 15 mm thick, across at least 2 floor boards. Wherever

possible, place the appliance in the corner of the room - there

wooden floors are most secure and least liable to resonance

vibrations.

Never compensate for small unevennesses in the floor by

placing wood, pasteboard or such like.

The front adjustable feet must be blocked after installation of

the appliance by means of the locking nuts.

Water connection

Connect the water inlet hose to a cold water tap with a 3/4" gas

threaded orifice, after having inserted the rugger sealing

washer into the hose collar. If the water connection is made

onto new pipes or onto pipes which have not been used for a

long time, it is advisable to run off a certain amount of water

before connecting the machine.

Place the curved end of the outled hose into a drain pipe having

a height between 70 and 100 cm from floor level or secure it to

a sink or bath tub. Make sure that the drain hose is firmly

secured so that it will not slip out or fall down from its position.

The water should drain freely and, consequently, the drain hose

should not be choked or placed in such a way as to obstruct the

normal water flow. If an extension hose is required, remember

that it might cause a malfunction in the drain pump, particularly

if the extension has a length in excess of 1 meter or if the

diameter of the extension is smaller than the diameter of the

original drain hose.

INSTALLATION

BE CAREFUL : The parts protecting the inner components of the machine during transit must all be removed before

using your machine for the first time. In order to avoid possible damage to the appliance, it is indispensable to take away

the polystyrene basis, the two loosened spacers at the back of the appliance and the polystyrene wedge (follow the

instructions of the unpacking sheet). Close imperatively the 2 holes left by the 2 spacers with the plugs provided with

the appliance ; do not forget to put on the central cover.

Electrical connection

Before fitting the plug into the wall socket, check the following

points :

1) The supply voltage of the domestic wiring system does not

fluctuate by more that 10%, plus or minus, from 230 V.

2) The meter, the fuses, the supply line and the wall socket are

suitable to carry the maximum load required by the machine

(2,3 kW).

Very important :

The washing machine is provided with a feeding wire with

earth connection: it must be connected to a plug like that

is provided with a good earth connection.

The replacing of the power cord must only be realized by

the After Sales Service.

The manufacturer declines any responsibility where the

previous recommendations are not followed.

Levelling

It is essential that your machine is absolutely level. Raise or

lower the front feet of the machine ; tighten the nuts of the feet

with an adjustable wrench.

Also make sure that the machine does not touch the wall, the

furnitures, etc. during the functioning in order to avoid vibra-

tions, noise or displacements of the appliance during operation.

Moving of the appliance

To move your washing machine, put it on its wheels by turning

from the right to the left the special level located at the bottom

of the appliance. Once the machine placed at the chosen

place, bring back the lever to its initial position.

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Zanussi TA833V Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver Zanussi TA833V