Zanussi ZGL62ITX Manuel d'utilisateur

ZGL 62GashobInstructionbookletGB

10Before any maintenance or cleaning can be carried out,Before any maintenance or cleaning can be carried out,Before any maintenance or cleaning can b

11The Ignition electrodeThe Ignition electrodeThe Ignition electrodeThe Ignition electrodeThe Ignition electrodeThe electric ignition is obtained thro

12Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local Service Force Centre.

13OVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONS Width: 580 mmDepth: 500 mmCUT OUT DIMENSIONSCUT OUT DIMEN

14BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 3.0 0.75 2.0 0

15Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th

16A)A)A)A)A ) End of shaft with nutB)B)B)B)B ) WasherC)C)C)C)C ) ElbowFO 0264InstallationIMPORIMPORIMPORIMPORIMPORTTTTTANTANTANTANTANTAny gas installa

17It is important to install the elbow corrIt is important to install the elbow corrIt is important to install the elbow corrIt is important to instal

18BBBBBuilding over a kitchen unituilding over a kitchen unituilding over a kitchen unituilding over a kitchen unituilding over a kitchen unitwith doo

19Fitting the Hob into the WorktopCarry out the building in of the hob as follows:1. put the seals supplied with the hob, on the edges of the cut out

2Thank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceT

20Electrical ConnectionsAny electrical work required to install this hob should beAny electrical work required to install this hob should beAny electr

21Wiring diagramPermanent ConnectionPermanent ConnectionPermanent ConnectionPermanent ConnectionPermanent ConnectionIn the case of a permanent connect

22Fault FindingPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Syst

23A. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKAppliance must be elect

24Check gas supply atburnerIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgn

25CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)

26Conversion from Natural Gas to LPGIMPORIMPORIMPORIMPORIMPORTTTTTANTANTANTANTANTThe replacement/conversion from natural gas to LPG should onlyThe rep

27Guarantee/Customer ServiceStandard guarantee conditionsStandard guarantee conditionsStandard guarantee conditionsStandard guarantee conditionsStanda

28Service and Spare PartsService and Spare PartsService and Spare PartsService and Spare PartsService and Spare PartsIn the event of your appliance re

29This appliance is guaranteed by Electrolux in each of the countries listedat the back of this user manual, for the period specified in the appliance

3ContentsImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety Information.

30

31

35687-8006 04/09 R.Awww.zanussi.co.uk

4Important Safety InformationYYYYYou MUST rou MUST rou MUST rou MUST rou MUST read these waread these waread these waread these waread these warnings

5z Ensure the control knobs are in the ‘OFF’ position when not in use.z When using other electrical appliances, ensure the cable does not comeinto con

61. Hob Top2. Rapid Burner3. Semi-rapid Burner4. Auxiliary Burner5. Control knobsDescription of the Hob312534

7INSTALLATIONAny gas installation must be carried out by a registeredAny gas installation must be carried out by a registeredAny gas installation must

8Lighting the burnersLighting the burnersLighting the burnersLighting the burnersLighting the burnersFor easier lighting, proceed before putting a pa

9Burner minimum maximumdiameter diameterLarge (rapid) 180 mm 260 mmMedium (semi-rapid) 120 mm 220 mmSmall (auxiliary) 80 mm 160 mmAs soon as a liquid