Zanussi ZWHB7140P Manuel d'utilisateur

ENUser manualWashing MachineZWHB 7140 P

• Directly into a drain pipe at a heightof not less than 60 cm and not more than100 cm.MAX 100cmThe end of the drainhose must always beventilated, i.e

If you require any further advice please contactyour local water authority.SHOWERWASHINGMACHINEDISHWASHERBATHSINKTOILETBIDETRAINWATER‘RUN-OFF’SURFACE

PersonalisationBuzzerThe appliance is provided with an acoustic de-vice, which sounds in the following cases:• at the end of the cycle;• if there is a

Rust: oxalic acid dissolved in hot water or arust removing product used cold. Be carefulwith rust stains which are not recent since thecellulose struc

For the quantity of detergent, refer always towhat is written on the product packing.Use less detergent if:• you are washing a small load,• the laundr

• Rotate the flapdownwards.• Carefully put thedrawer back.• Measure out the detergent.For the quantity of detergent, refer al-ways to what is written

2 3 45 69107 811Programme selectordialMini 30’Mix 20°SyntheticsWool/HandwashDelicatesSpecialsBlanketEasy IronCottonsCottons+PrewashCottons RinseDrainS

3Spin ReductionBy selecting a programme, the appliance proposes automati-cally the maximum spin speed provided for that programme.Press this button re

4+6Extra RinseThis appliance is designed for saving water. However, forpeople with very delicate skin (allergic to detergents) it maybe necessary to r

8Delay StartDelay StartThe programme can be delayed from 30 min - 60 min - 90min, 2 hours and then by 1 hour up to a maximum of 20 hoursby means of th

ContentsSafety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _

•To restart the programme from the point at which it wasinterrupted, press the button 9.• After the programme has started the door is locked. If, f

Door sealAt the end of everycycle, check from thedoor seal and re-move objects thatcould be trapped inthe fold.Washing programmesProgramme - Maximum a

Programme - Maximum and Minimum Temperature -Cycle Description - Maximum Spin Speed - MaximumFabrics Load - Type of LaundryOptionsDetergentCompartment

Programme - Maximum and Minimum Temperature -Cycle Description - Maximum Spin Speed - MaximumFabrics Load - Type of LaundryOptionsDetergentCompartment

Programmes Load(kg)Energy con-sumption(kWh)Water con-sumption (litre)Approximateprogrammeduration (mi-nutes)Remainingmoisture(%)1)Standard cotton prog

• Use a stiff brush to clean and remove allwashing powder residue.• Clean all the removed parts of the dis-penser drawer under a tap to remove anytrac

The filter is inserted correctly when theindicator on its top is visible andblocked.• close the filter cov-er;• insert the mainsplug again.Cleaning th

Fault code and mal-functionPossible cause / SolutionProblem with the watersupplyThe water tap is closed.• Open the water tap.The inlet hose is squashe

Malfunction Possible cause / SolutionThe appliance does notstart:The plug is not properly inserted in the power socket.• Insert the plug into the powe

Malfunction Possible cause / SolutionSpinning starts late orthe appliance does notspin:The electronic unbalance detection device has cut in because th

• Obey the maximum load volume of 7 kg (refer to the “Pro-gramme chart” chapter).• If the supply cord is damaged, it must be replaced by the manu-fact

30 www.zanussi.com

31www.zanussi.com

www.zanussi.com/shop 192976840-A-492013

This appliance complies with the E.E.C. Di-rectives.Water connection• Make sure not to cause damage to the wa-ter hoses.• The appliance is to be conne

7. screw the water inlet hose to the tap andthe drain hose to the rear of the applianceagain;When you intend to start the appliance upagain, make sure

1 Detergent dispenser drawer2 Worktop3 Control panel4 Door opening handle5 Rating plate (on the inner edge)6 Front adjustable feet7 Water drain hose8

x 3x 3x 2x 1BACWarning! Remove and keep alltransit devices so that they can be re-fitted if the appliance ever has to be trans-ported again.Necessary

• Unscrew the three bolts and remove thehose holders.• Slide out the relevant plastic spacers.Warning! Donot removethe drain hosefrom the rear sup-por

Accurate levelling prevents vibration, noiseand displacement of the appliance duringoperation.Repeat the levelling action, if the applianceis not leve